- 6.4.3.3 Packet Tracer
- 6.4.3.3 Packet Tracer Answer
- 6.4.3.3 Packet Tracer Lab Answers
- Packet Tracer 6.4.3.3 Solutions
- Cisco Packet Tracer 7.3.1 download link for Windows (10, 8.1, 7.0) 64 bits edition. Cisco Packet Tracer 7.3.1 download link for Windows (10, 8.1, 7.0) 32 bits edition.
- Cap 6/ 6.5.1.2 Packet Tracer Skills Integration Ch. Cap 6/ 6.5.1.1 Class Activity - Can you read this map; Cap 6/ 6.4.3.4 Packet Tracer - Troubleshooting Def. Cap 6/ 6.4.3.3 Packet Tracer - Connect a Router to. Cap 6/ 6.4.1.2 Packet Tracer - Configure Initial R. Cap 6/ 6.3.1.10 Packet Tracer.
- Proef/oefen tentamen Oktober 2018, vragen en antwoorden 6.4.1.3 Packet Tracer - Configure Initial Router Settings Summary of CB Concepts and Theories Portfolio - Samenvatting Network Management 1 Introductie in management Parasitologie (Devos).
Packet Tracer – Configuring Basic EIGRP with IPv6 (Instructor Version)
Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only.
Topology
Addressing Table
6.4.3.3 Packet Tracer
4.3.3.4 Packet Tracer – Configuring VPN Tunnel Mode Answers Packet Tracer – Configuring VPN Tunnel Mode (Answers Version) Answers Note: Red font color or gray highlights indicate text that appears in the Answers copy only. Addressing Table Device Private IP Address Subnet Mask Site File Backup Server 10.44.2.254 255.255.255.0 Gotham Healthcare Branch Objectives Part 1: Continue reading.
Objectives
Part 1: Configure EIGRP for IPv6 Routing
Part 2: Verify IPv6 EIGRP for IPv6 Routing
Scenario
In this activity, you will configure the network with EIGRP routing for IPv6. You will also assign router IDs, configure passive interfaces, verify the network is fully converged, and display routing information using show commands.
Wapka facebook phishing code 2020. EIGRP for IPv6 has the same overall operation and features as EIGRP for IPv4. There are a few major differences between them:
EIGRP for IPv6 is configured directly on the router interfaces.
With EIGRP for IPv6, a router-id is required on each router or the routing process will not start.
The EIGRP for IPv6 routing process uses a 'shutdown' feature.
Part 1: Configure EIGRP for IPv6 Routing
Step 1: Enable IPv6 routing on each router.
Step 2: Enable EIGRP for IPv6 routing on each router.
6.4.3.3 Packet Tracer Answer
The IPv6 routing process is shutdown by default. Issue a command that will enable EIGRP for IPv6 routing in R1, R2 and R3.
Enable the EIGRP process on all routers and use 1 as the Autonomous System number.
Step 3: Assign a router ID to each router.
The router IDs are as follows:
- R1: 1.1.1.1
- R2: 2.2.2.2
- R3: 3.3.3.3
Step 4: Using AS 1, configure EIGRP for IPv6 on each interface.
Part 2: Verify EIGRP for IPv6 Routing
Step 1: Examine neighbor adjacencies.
Use the command show ipv6 eigrp neighbors to verify that the adjacency has been established with its neighboring routers. The link-local addresses of the neighboring routers are displayed in the adjacency table.
Step 2: Examine the IPv6 EIGRP routing table.
Use the show ipv6 route command to display the IPv6 routing table on all routers. EIGRP for IPv6 routes are denoted in the routing table with a D.
Step 3: Verify the parameters and current state of the active IPv6 routing protocol processes.
Use the command show ipv6 protocols to verify the configured parameter.
Step 4: Verify end-to-end connectivity.
PC1, PC2, and PC3 should now be able to ping each other. If not, troubleshoot your EIGRP configurations.
6.4.3.3 Packet Tracer Lab Answers
[sociallocker id='8545″]
[wpdm_package id='10423′]
Packet Tracer 6.4.3.3 Solutions
[/sociallocker]
